Particle Filter Sundström SR 510 P3




- Product Code: H02-1312
- Available in stock 96 pcsThe product will be sent in 1-3 days
- Check store availability here
- Delivery costs starting from 10,04 €Pick up from the store0,00 €
Sundström SR 510 P3 R particle filter for respirators and powered air systems
The Sundström SR 510 P3 R is a high-efficiency particle filter for dust, smoke, mist, fibres and other solid or liquid particles. It is compatible with Sundström SR 100, SR 200 and SR 900 respirators and with SR 500, SR 500 EX and SR 700 powered air-purifying respirators.
Product number: H02-1312
Pricing: Net price
Availability: Immediately available from the Turku and Kerava stores.
Key features
- Reusable P3 R particle filter.
- Designed for all types of particulate contaminants, including dust, smoke, mist, fibres and liquid aerosols.
- Manufacturer-stated filtration efficiency of more than 99.997% when tested with paraffin oil.
- Compatible with Sundström half masks, full-face masks and approved powered air systems.
- Can be combined with a Sundström gas filter when both particles and gases or vapours are present.
- Designed for use with the SR 221 pre-filter. Regular pre-filter replacement helps extend the service life of the main filter.
P3 particle filter or gas filter?
Filter selection starts with identifying the form of the contaminant. A P3 particle filter is intended for dust and other particulate contaminants. Visible dust, smoke or mist consists of particles or aerosols, but many harmful particles cannot be seen with the naked eye. Gases and vapours are also often invisible.
Gases and vapours require a gas filter selected for the specific substance. An A-type filter is intended for certain organic gases and vapours and does not protect against every type of gas. Other contaminants may require a B, E or K filter. Always select the filter according to the workplace risk assessment and the identified contaminant.
Mould protection and demolition work
A P3 filter is used for protection against mould particles and fine dust. It can therefore be used as part of a correctly selected, tight-fitting respirator system during the demolition of a mould-damaged building. Depending on the risk assessment, work in moisture-damaged buildings may also require an A2 gas filter in addition to the P3 particle filter.
The Finnish Institute of Occupational Health recommends a powered respirator for prolonged dusty work. You can start with an SR 200 full-face mask and later expand the system with a separately purchased compatible Sundström fan unit and breathing hose. This creates a powered air-purifying respirator system. It is not the same as a supplied-air respirator receiving air from an external clean-air source.
Filter replacement
- Replace the P3 particle filter if it is damaged or if breathing resistance becomes uncomfortable.
- Follow all powered respirator alarms and the manufacturer's filter replacement instructions.
- If you can smell or taste the contaminant, stop work and leave the exposure area. A P3 filter does not protect against gases or vapours.
- Replace a gas or combined filter at the latest when the smell or taste of the contaminant breaks through. Do not rely solely on smell, as some hazardous substances cannot be detected safely by odour.
- SR 500 and SR 500 EX fan units must always be fitted with two identical filters, which must be replaced at the same time.
Storage
Store an opened filter in a clean and dry place at room temperature. For longer-term storage, seal the filter in an airtight bag or container to protect it from moisture and contaminants. Always store the filter outside the exposure area and follow the manufacturer's instructions.
Safety and compliance
- Filter class: P3 R
- Standards: EN 143:2000+A1:2006, EN 12941:1998+A2:2008 and EN 12942:1998+A2:2008
- R marking: designed for use for more than one work shift when used in accordance with the manufacturer's instructions
- Does not protect against gases, vapours, oxygen deficiency or unknown contaminants without suitable additional protection
Technical information
- Brand: Sundström
- Model: SR 510
- Product number: H02-1312
- Type: mechanical particle filter
- Filter class: P3 R
- Material: PP
- Colour: black
- Operating temperature: -10 to +55 °C, relative humidity below 90%
- Storage temperature in unopened packaging: -20 to +40 °C, relative humidity below 90%
View the Sundström SR 510 P3 R particle filter on the manufacturer's website
